![]() When installed as a pair and aimed in accordance with your state's regulations, the Driving White pattern meets SAE J581 standard as a Driving/Auxiliary High Beam Light, and the Fog pattern meets SAE J583 standard as a Foglamp, for legal on-road use. Choose your output color of cool white or yellow, which is often said to help cut through inclement weather. It serves as a great upgrade for any factory foglamp, and will fully illuminate the area in front of your vehicle. ![]() SAE Fog provides an extremely wide field of view, with high-intensity output over an entire 80-degree spread. Rather than a traditional "spot" pattern, the Stage Series Driving pattern shines in an 18x8 degree spread, providing just enough width to fully illuminate the road ahead at high speeds. SAE Driving is designed to supplement your high beams, but it’s great for general illumination as well. Thanks to this innovative feature, when coupled with high-intensity LED chips, the total intensity of the SS3 is much greater than other LED pods using basic optics or reflectors with a standard outer lens. Click here to learn more: Total Internal Reflection (TIR) Optics | Stage Series Video.įrom there, while other options on the market lose as much as 10% of the light output shining through an outer lens, the custom-molded TIR optic in the SS3 serves as both the optic and main lens for greater efficiency and light output. Instead, the custom-engineered TIR optic in the SS3 collects all of the light from the LED, and directs it only where you need it, drastically reducing glare and improving total efficiency. Ocused. Traditional optics like reflectors or simple lenses lose light internally and to glare, so not all of the light shines on target. Simply remove your factory fog light assembly and ours will bolt right in its place! Wire adapters are included to connect the lights to your factory bulb sockets - no additional wiring needed! Plug and Play. Thanks to custom-molded brackets, the SS3 Fog Light Bracket Kit can be installed on your Subaru WRX in minutes. With the included round bezel, the SS3 Fog Kit has a clean, factory-style appearance, only much brighter! Overview. Upgrade the fog lights on your Subaru WRX with our SS3 Fog Light Bracket Kit! Featuring higher output intensity than any other 3” light on the market, these LED pods have been designed for maximum functionality, with custom-engineered TIR optics shining in highly useful beam patterns, all in a durable package. Includes round bezel, for factory-style appearanceĪdvanced TIR optics provide high efficiency and focus Step 8: Test your LED daytime running light fog bezel for functionality.Direct replacement for Subaru WRX fog lamps Since there is only one pin port for the ACC connection, you can bend or cut off one of the pins on the fuse adapter. Step 7: Connect the black wire to the negative(-) car battery connection and the red wire to the ACC 12V positive(+) connection in the fuse box. ![]() Not only will this keep the wiring cooler, but also ensure the wires are long enough. Step 6: Route the wiring harness below the radiator. Essentially, the wiring harness is plugged in between the turn signal bulb and turn signal harness. Plug in the harness adapter (indicated as #2) back into the turn signal bulb. Plug the stock turn signal harness into the wiring harness, marked as #1 in the diagram above. Unplug the turn signal harness from the turn signal bulb. Step 5: In this diagram below, we've already disconnected the turn signal harness from the turn signal bulb (circled in red). This will give you access to the rear fog light area. Step 4: Undo the plastic clips holding the bumper and wheel well together. Step 3: Connect the new switchback LED DRL foglamp bezel to the module box cable. Pull out the LED DRL module box adapter out from the fog lamp area. Step 2: Drop the wiring harness and module box down from the engine bay. In this diagram, the included module box is connected to the included wiring harness. ![]() You can either use a flathead screwdriver to pry out the bezel or simply pull it out using your hand. Step 1: Detach your stock foglight bezel from your bumper. Using these switchback LED DRLs will make you be seen and earn you some style points with its super glossy look against your paint job. With an updated fog lamp bezel comes an updated installation guide. This tutorial will show you how to install the switchback LED daytime running light fog bezel for the 2015-2017 Subaru WRX/STi (70-811).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |